Perfect for Stick Welding Areas
The H.T. Runner is the ideal surface for high temperature, high demand stick welding areas where traction and floor protection are the primary objectives. The specially formulated rubber has an extraordinarily high ignition point of 500 degrees Fahrenheit and resists damage from stick welding slag and splatter.
For high temperature resistance and ergonomics, check out WeldSafe No. 447.
Need additional height to properly weld? Use H.T. Welding Runner on top of FOUNDATION Smooth Platforms to improve reach and safety.
| SKU | Short Description | Color | Thickness | Dimensions | Stock Part | UOM |
|---|---|---|---|---|---|---|
| 347.564x3x75BK | H.T. Runner | Black | 5/64" | 3' x 75' | Yes | RL |
| 347.564x4x75BK | H.T. Runner | Black | 5/64" | 4' x 75' | Yes | RL |
Parameters of Category: Specifications - General
| Suitable Environment | Dry |
| Type | Runner |
| Customization Level | C1- Custom Length |
| Solid or Drainage | Solid |
| Compound | Natural Rubber Surface |
| Recycled | >20% |
| Warranty | 1 Years |
- Formulate high-temp rubber
- Ignition point of over 500⁰ Fahrenheit (200⁰ Celsius) designed for welding
- Resist pitting and damage from slag and splatter
- Install for aisle ways in facilities or transportation vehicles
- 5/64" thick
Learn more about Wearwell's welding solutions here.
Test Specification & Results
| Property | Test / Result |
|---|---|
| Flammability | MVSS 302 / 'A'; Rating. |
| Taber Abrasion | Federal Standard 191 / 1% lost @ 1,000 cycles |
| Temperature Range | 500 F Melt Point |
| Coefficient of Friction | ASTM F1677 / Dry: COF = 1.10 / Wet COF = .32 |
| Compression Deflection | ASTM D575 / Deflection @ 35 psi, mm=7.85 |
| Tear Strength | Not Available |
| ESD Rating | Not Available |
| Dielectric Strength | Not Available |
Key
- A = Performs well
- B = Slightly affected
- C = Moderately affected
- D = Highly affected
- U = Not recommended
- NT = Not tested
| Chemical | Urethane | Nitrile | PVC | CFR | SBR | Natural Rubber |
|---|---|---|---|---|---|---|
| Acetone | U | U | U | C | C | C |
| Animal Fats | NT | A | C | U | U | U |
| Bleach Solution (10% Dilute) | NT | B | B | C | C | C |
| Boric Acid | B | A | A | A | A | A |
| Brake Fluid | U | A | B | D | D | D |
| Brake Fluid (Silicone Based) | U | A | B | A | B | B |
| Chlorine Solution (3% Dilute) | C | A | B | C | C | C |
| Citric Acid | NT | A | C | C | C | U |
| Cutting Fluid (Mineral Oil Based) | U | B | B | B | C | D |
| Diesel Oil | U | A | B | U | U | U |
| Ethylene Acetate | NT | U | NT | U | U | U |
| Ethylene Glycol | B | A | A | A | A | A |
| Hydraulic Oil (Petroleum) | U | A | B | D | D | D |
| Hydrochloric Acid Cole (37% Dilute) | U | C | C | B | B | B |
| Isopropyl Alcohol | A | B | A | B | B | A |
| Lacquer Solvents | U | U | U | U | U | U |
| Lindol (Hydraulic Fluid) | NT | U | NT | U | U | U |
| MEK | U | U | U | U | U | U |
| Mineral Oil | C | A | B | A | B | U |
| Naptha | NT | C | U | U | U | U |
| Napthlene | U | U | U | U | U | U |
| Petroleum | U | C | B | D | D | D |
| Salt Water | A | A | B | B | B | C |
| Tolulene | U | U | U | U | U | U |
| Transmission Fluid (Type A) | U | B | A | C | U | U |
| Trichloroethane | U | U | U | U | U | U |
| Vegetable Oil | C | A | B | C | C | C |
Q: Can I glue the 347 runner to the floor?
A:Yes, you can! Semi-permanent installations can be accomplished with common mastics. Please contact your local home improvement store for the best adhesive recommendation for rubber to whatever type of substrate you're adhering to. (i.e. concrete, wood, steel, etc.)
Q: If I purchase a full roll, will I be able to cut it to the lengths that I need?
A:Yes, you can! It's very easy to cut this material to size. All you need is a straight edge and a pair of shears or utility knife. Safety first! Always wear cut resistant gloves when cutting.
Q: What's the life expected life of this product?
A:The life expectancy can vary dramatically depending on a multitude of factors such as: foot traffic, exposure to oils, caustic chemicals or fluids, excessive temperatures, cleaning and maintenance schedule, compound, etc. The following are general guidelines based on our customers’ experience (your experience may vary): Average lifespan is 1 - 2 years.
